 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 9 matches |
| Author | Message |
|---|---|
 Topic: Problem presetting data into data EEPROM |
|
| TCC Replies: 5 Views: 14363 |
 Forum: General CCS C Discussion Posted: Fri Apr 23, 2010 3:20 am Subject: Problem presetting data into data EEPROM |
| Hi,
I need to preset some data into data EEPROM and from CCS Help manual, there is something like #rom 0x2100={01,02,03,04,05,06,07}. I tried it in my program, it couldn't work. Anyone can help? ... |
|
| Topic: problem with comparator interrupt |
|
| TCC Replies: 5 Views: 8334 |
Forum: General CCS C Discussion Posted: Mon Apr 05, 2010 10:38 pm Subject: problem with comparator interrupt |
| I am using PCM V 4.106. | |
| Topic: problem with comparator interrupt |
|
| TCC Replies: 5 Views: 8334 |
Forum: General CCS C Discussion Posted: Mon Apr 05, 2010 7:46 pm Subject: problem with comparator interrupt |
| Hi,
I have problem triggering the comparator interrupt, when C1+/AN2 input is greater than C1-/AN0 input (this threshold is fixed at 0.207V). I expect the interrupt to trigger, it just don't happe ... |
|
| Topic: RS-232 PIC16F1827 |
|
| TCC Replies: 6 Views: 7485 |
Forum: General CCS C Discussion Posted: Tue Mar 02, 2010 3:52 am Subject: RS-232 PIC16F1827 |
| Hi,
When running with external crystal (in HS mode), I found that the timing of this 1827 chip is always 4x faster of my settings. For example, during delay_ms(500), i am getting 125ms instead o ... |
|
| Topic: RS-232 PIC16F1827 |
|
| TCC Replies: 6 Views: 7485 |
Forum: General CCS C Discussion Posted: Mon Mar 01, 2010 7:36 pm Subject: RS-232 PIC16F1827 |
| Hi Ttelmah
Thanks for your suggestion, i have a line 'setup_oscillator(OSC_4MHZ)' and it work slightly better..but it still output garbage. I measured the bit rate from the scope and found that ... |
|
| Topic: RS-232 PIC16F1827 |
|
| TCC Replies: 6 Views: 7485 |
Forum: General CCS C Discussion Posted: Mon Mar 01, 2010 1:07 am Subject: RS-232 PIC16F1827 |
| Yes, my setting in HyperTerminal is correct.
I complied with MPLAB, PCM version 4.105 |
|
| Topic: RS-232 PIC16F1827 |
|
| TCC Replies: 6 Views: 7485 |
Forum: General CCS C Discussion Posted: Mon Mar 01, 2010 12:17 am Subject: RS-232 PIC16F1827 |
| Hi,
I have written a test program but I have problem trying to transmitting out correctly to my PC's COM port using rs-232. The hyperterminal output shows €€€€€€€€€€€€� ... |
|
| Topic: Problem with PIC16F1827.h |
|
| TCC Replies: 3 Views: 6826 |
Forum: General CCS C Discussion Posted: Wed Feb 10, 2010 1:12 am Subject: Problem with PIC16F1827.h |
| now using PIC16F1827
Complied with MPLAB, PCM version 4.038 I don't think vs. 4.038 supports the 16F1827. I deleted the 16F1827.h file from my installation of 4.104, and then installed 4.038, a ... |
|
| Topic: Problem with PIC16F1827.h |
|
| TCC Replies: 3 Views: 6826 |
Forum: General CCS C Discussion Posted: Wed Feb 10, 2010 12:40 am Subject: Problem with PIC16F1827.h |
| Previously using PIC16F690, now using PIC16F1827
Complied with MPLAB, PCM version 4.038 The following errors are as shown below: *** Error 7 "C:\PROGRA~1\PICC\devices\16F1827.h" Line ... |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group