 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 7 matches |
| Author | Message |
|---|---|
 Topic: GENERATING PWM USING THE TIMER |
|
| akin54 Replies: 3 Views: 15259 |
 Forum: General CCS C Discussion Posted: Fri Mar 04, 2022 1:50 am Subject: GENERATING PWM USING THE TIMER |
| Yes, now I see. I made the MCLR pin a hardware button. | |
| Topic: GENERATING PWM USING THE TIMER |
|
| akin54 Replies: 3 Views: 15259 |
Forum: General CCS C Discussion Posted: Fri Mar 04, 2022 1:49 am Subject: GENERATING PWM USING THE TIMER |
| #include <main.h>
#FUSES NOMCLR //MCLR = A3 pin #int_timer2 void timer2 () { output_high(pin_a5); delay_us(12); outp ... |
|
| Topic: GENERATING PWM USING THE TIMER |
|
| akin54 Replies: 3 Views: 15259 |
Forum: General CCS C Discussion Posted: Fri Mar 04, 2022 12:27 am Subject: GENERATING PWM USING THE TIMER |
| Hello everyone.
I want to generate pwm from this processor (PIC12F683) without using the ccp1 leg. I want to use the GP5(A5) pin for this operation. The electronic card circuit I have drawn does not ... |
|
| Topic: Generate pwm square wave at 300 khz frequency PIC18F47Q43 |
|
| akin54 Replies: 1 Views: 10908 |
Forum: General CCS C Discussion Posted: Thu Dec 09, 2021 11:51 pm Subject: Generate pwm square wave at 300 khz frequency PIC18F47Q43 |
|
SETUP_PWM1(PWM_ENABLED | PWM_CLK_FOSC | PWM_CLK_DIV_BY_1); set_pwm1_period(24); set_pwm1_duty(1,12) ... |
|
| Topic: PIC18F47Q43 SPI communication problem |
|
| akin54 Replies: 10 Views: 27306 |
Forum: General CCS C Discussion Posted: Fri Nov 12, 2021 1:55 pm Subject: PIC18F47Q43 SPI communication problem |
| Using #USE SPI, you should be using spi_xfer, not spi_read or spi_write.
Basically the spi_read, write and setup_spi, are the 'old' commands. #USE, with spi_xfer are the new commands. You should not ... |
|
| Topic: PIC18F47Q43 SPI communication problem |
|
| akin54 Replies: 10 Views: 27306 |
Forum: General CCS C Discussion Posted: Fri Nov 12, 2021 8:23 am Subject: PIC18F47Q43 SPI communication problem |
| 2nd spi write data is 0, so pot wiper would be zero ?
Have you got the pot wired to VDD and VSS ? What speed is the PIC ? Does the PIC flash an LED at 1Hz ? Is the spi 'mode' correct for that dev ... |
|
| Topic: PIC18F47Q43 SPI communication problem |
|
| akin54 Replies: 10 Views: 27306 |
Forum: General CCS C Discussion Posted: Fri Nov 12, 2021 7:47 am Subject: PIC18F47Q43 SPI communication problem |
| #use spi (MASTER, CLK=PIN_D0, DI=PIN_D3, DO=PIN_D1, BAUD=4000000, MODE=0, BITS=8, STREAM=SPI_1)
setup_spi(SPI_MASTER | SPI_H_TO_L ); output_low(pin_d0); spi_write(0x ... |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group