CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Search found 13 matches
CCS Forum Index
Author Message
  Topic: MPLAB X IDE compatible with CCS compilers ?
davidpk

Replies: 8
Views: 27154

PostForum: General CCS C Discussion   Posted: Thu Jun 25, 2015 6:42 am   Subject: MPLAB X IDE compatible with CCS compilers ?
Wow, this really proves to me that X was such a good idea... Rolling Eyes

I'm struggling myself and don't have any real advice, I just wanted you to know you're not alone.

David
  Topic: SM Bus and I2C Bus
davidpk

Replies: 6
Views: 15190

PostForum: General CCS C Discussion   Posted: Wed Feb 21, 2007 1:49 pm   Subject: SM Bus and I2C Bus
At my request, CCS recently added a delay to satisfy a start condition hold time. You need to include an SMBus declaration in your #use i2c line:

#use i2c( Stream=BAT1, Master, sda=PIN_D6, scl=PIN_ ...
  Topic: HS & PLL on 18F452
davidpk

Replies: 5
Views: 10083

PostForum: General CCS C Discussion   Posted: Wed Oct 27, 2004 8:19 am   Subject: HS & PLL on 18F452
That was the one!

Thanks asmallri!
  Topic: HS & PLL on 18F452
davidpk

Replies: 5
Views: 10083

PostForum: General CCS C Discussion   Posted: Tue Oct 26, 2004 6:52 pm   Subject: HS & PLL on 18F452
I'm trying to use the PLL for the first time and I'm having some trouble:

In my #delay() statement do I use the real crystal or the x4 frequency?
Is the baud rate generated from the real or the mu ...
  Topic: MPLAB 6.6
davidpk

Replies: 3
Views: 9541

PostForum: General CCS C Discussion   Posted: Sun Oct 24, 2004 2:28 pm   Subject: MPLAB 6.6
I've seen this and I've asked about it on both forums. They both point fingers at the other.

The good news is that I just installed v6.62 and it's not doing that... it may start it again the next ...
  Topic: Hardware flow control of UART
davidpk

Replies: 8
Views: 14756

PostForum: General CCS C Discussion   Posted: Thu Sep 16, 2004 3:06 pm   Subject: Hardware flow control of UART
I had this exact same problem with an 18F452 running at 40MHz and my desktop PC. The communication from the PC to the PIC was only single characters but the PIC would respond with a lot of data (100's ...
  Topic: a 5volt regulator cost 5mha in current?
davidpk

Replies: 8
Views: 16233

PostForum: General CCS C Discussion   Posted: Thu Aug 05, 2004 10:14 am   Subject: a 5volt regulator cost 5mha in current?
I looked at the MAX1759 part and it would be really good for loads of less than 20mA. Li-ion cells would be great since their voltage doesn't drop to below 3.6V until they are nearly dead.

The d ...
  Topic: I2C issues... can't get an ACK. Big demo tommorow :(
davidpk

Replies: 6
Views: 15379

PostForum: General CCS C Discussion   Posted: Thu Jul 22, 2004 12:05 pm   Subject: I2C issues... can't get an ACK. Big demo tommorow :(
Are you sure you didn't accidentally change the device address with your drivers? Can you look at the signals on an O'Scope?
  Topic: off topics : looking for datasheet
davidpk

Replies: 4
Views: 11791

PostForum: General CCS C Discussion   Posted: Fri Jun 18, 2004 2:12 pm   Subject: off topics : looking for datasheet
The bottom of the data sheet says you need to sign an NDA before they'll give you the real one.
  Topic: i2c Question
davidpk

Replies: 5
Views: 11922

PostForum: General CCS C Discussion   Posted: Thu Jun 17, 2004 4:21 pm   Subject: i2c Question
Joan,

I haven't ever used the I2C slave mode but the CCS manual says you must use the hardware for slave mode. (See the #use i2c in the pre-processor section)

Does this help?

David
  Topic: 3pin resonator
davidpk

Replies: 8
Views: 17984

PostForum: General CCS C Discussion   Posted: Sun May 23, 2004 3:14 pm   Subject: 3pin resonator
All of the data sheets I've just browsed for these parts show the connections exactly as you have done. None of the data indicate that this would work, but I would try it in a pinch, swap the OSC1 and ...
  Topic: 3pin resonator
davidpk

Replies: 8
Views: 17984

PostForum: General CCS C Discussion   Posted: Sun May 23, 2004 1:05 pm   Subject: 3pin resonator
A manufacturer and part number for your part would help. (The resonator, not the PIC Wink )
  Topic: 16F628 USART by internal OSC
davidpk

Replies: 2
Views: 9438

PostForum: General CCS C Discussion   Posted: Thu May 13, 2004 2:20 pm   Subject: 16F628 USART by internal OSC
I am using an 18F452 at 40MHz. I was sending out data at 115,200 and things were working fine until I tried to send out a long string. I reduced the bps to 57,600 and it is working fine.

RS-232 ca ...
 
Page 1 of 1
All times are GMT - 6 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group