 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 8 matches |
| Author | Message |
|---|---|
 Topic: Debugging in MPLAB X - Can only set breakpoints some places |
|
| dcm684 Replies: 2 Views: 11471 |
 Forum: General CCS C Discussion Posted: Fri May 31, 2019 8:23 pm Subject: Debugging in MPLAB X - Can only set breakpoints some places |
| Thanks PCM. There was a mix of line endings, which are now fixed (and will be kept in check through a precompile script calling AStyle). Unfortunately, I'm still running into the same problems.
Bre ... |
|
| Topic: Debugging in MPLAB X - Can only set breakpoints some places |
|
| dcm684 Replies: 2 Views: 11471 |
Forum: General CCS C Discussion Posted: Fri May 31, 2019 2:33 pm Subject: Debugging in MPLAB X - Can only set breakpoints some places |
| I am trying to figure out why I can only set breakpoints on part of my program in MPLAB X. For the first 1/3 of of the program, I can click in the sidebar and get a working breakpoint. If I try to set ... | |
| Topic: Cannot set some pins to digital when #pin_select is used |
|
| dcm684 Replies: 3 Views: 12424 |
Forum: General CCS C Discussion Posted: Tue Jun 19, 2018 10:39 am Subject: Cannot set some pins to digital when #pin_select is used |
| Thanks newguy.
I went deeper into it and found that if I clear the bit, IOLOCK, I can change the values in ANCON3. I then re-set IOLOCK. This requires the fuse NOIOL1WAY. Another interesting tid ... |
|
| Topic: Cannot set some pins to digital when #pin_select is used |
|
| dcm684 Replies: 3 Views: 12424 |
Forum: General CCS C Discussion Posted: Mon Jun 18, 2018 3:08 pm Subject: Cannot set some pins to digital when #pin_select is used |
| I am working on a PIC18F97J94 with CCS PCH 5.075. I am trying, and failing, to set several pins on the H port to digital when I use #pin_select. I have no issues setting the non-H-port pins to digital ... | |
| Topic: #if defined() Usage |
|
| dcm684 Replies: 4 Views: 9832 |
Forum: General CCS C Discussion Posted: Wed Apr 09, 2014 11:38 am Subject: #if defined() Usage |
| Actually, "ANIMAL" is not defined. Its a value that I periodically #define for certain production environments. I'm sorry that I did not state that earlier.
I copied and pasted my code st ... |
|
| Topic: #if defined() Usage |
|
| dcm684 Replies: 4 Views: 9832 |
Forum: General CCS C Discussion Posted: Wed Apr 09, 2014 9:02 am Subject: #if defined() Usage |
| I have the following block of code in my program
#if (defined(ANIMAL) && (ANIMAL == COW)) /* Do stuff here */ #endif The compiler throws the warning "Und ... |
|
| Topic: Stack Size and Profiling |
|
| dcm684 Replies: 2 Views: 4358 |
Forum: General CCS C Discussion Posted: Wed Sep 08, 2010 11:42 am Subject: Stack Size and Profiling |
| That limit is for 16F. For 18F it's 31 stack levels.
Okay. I am using an 18f chip. So it looks like the stack is not the cause of those other problems. Thanks. |
|
| Topic: Stack Size and Profiling |
|
| dcm684 Replies: 2 Views: 4358 |
Forum: General CCS C Discussion Posted: Wed Sep 08, 2010 11:15 am Subject: Stack Size and Profiling |
| I was reading through the FAQ and noticed that the sum of my stack usage should be less than 9. Currently my stack usage is 14 (7 in main + 7 in ISR).
Is there a software means of profiling my stac ... |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group