 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 7 matches |
| Author | Message |
|---|---|
 Topic: Help with RN4020 BLE radio and pointer variables |
|
| ffotsch Replies: 2 Views: 13116 |
 Forum: General CCS C Discussion Posted: Sat Oct 11, 2014 9:23 am Subject: Help with RN4020 BLE radio and pointer variables |
| I am trying to use the new Microchip RN4020 BLE module to send a 2byte value to my iPad. Everything works fine, however my variable named value only increments once. I am fairly certain the radio is s ... | |
| Topic: spi_xfer error() on v.115 PCH? |
|
| ffotsch Replies: 4 Views: 6968 |
Forum: General CCS C Discussion Posted: Wed Dec 15, 2010 12:33 pm Subject: spi_xfer error() on v.115 PCH? |
| Yes, those are the hardware pins for SPI. However, it is my understanding and experience that spi can also be done in software without using the hardware pins. I have two spi devices on the same chi ... | |
| Topic: spi_xfer error() on v.115 PCH? |
|
| ffotsch Replies: 4 Views: 6968 |
Forum: General CCS C Discussion Posted: Wed Dec 15, 2010 6:09 am Subject: spi_xfer error() on v.115 PCH? |
| I am using a PIC 18f2550 with two spi slaves, one uses hardware spi and the other uses software spi. Here are my use statements:
#use spi(MODE=3, DI=PIN_a2, DO=PIN_a3, CLK=PIN_a1, BITS=16, STR ... |
|
| Topic: USB data type error |
|
| ffotsch Replies: 4 Views: 4581 |
Forum: General CCS C Discussion Posted: Fri Nov 14, 2008 9:20 pm Subject: USB data type error |
| FvM you were correct. My HyperTerminal was in V52 and when I switched to ANSI I saw all 256 chr. I also observed all in another program. So the problem is in VB.net. It must be using the MSB as a ... | |
| Topic: USB data type error |
|
| ffotsch Replies: 4 Views: 4581 |
Forum: General CCS C Discussion Posted: Fri Nov 14, 2008 11:31 am Subject: USB data type error |
| I have a USB serial connection established between an 18f2553 and a PC. I am using VB.net to receive bytes from the PIC. I am using the USB to UART emulator. The problem is I can't send a value grea ... | |
| Topic: Need help reading Serial data from the GPS receiver into PIC |
|
| ffotsch Replies: 1 Views: 7213 |
Forum: General CCS C Discussion Posted: Wed Sep 17, 2008 4:58 am Subject: Need help reading Serial data from the GPS receiver into PIC |
| I'm no expert, but I did a similar project with a hot air balloon. Set the GPS to NMEA output and the gps starts sending NMEA strings updated each second. Check the web site in the code for the form ... | |
| Topic: Help with 18f2550 Bootloader |
|
| ffotsch Replies: 0 Views: 2481 |
Forum: General CCS C Discussion Posted: Sun Sep 14, 2008 1:03 pm Subject: Help with 18f2550 Bootloader |
| I am wanting to use the CCS ex_usb_bootlader.c with an 18f2550. Can I simply change the device type from 4550 to 2550 and compile a working loader?
Thanks |
|
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group