CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Search found 8 matches
CCS Forum Index
Author Message
  Topic: 18F4580 - Can't run #INT_EXT
kansusid

Replies: 6
Views: 5179

PostForum: General CCS C Discussion   Posted: Fri Aug 14, 2009 3:45 am   Subject: 18F4580 - Can't run #INT_EXT
how do you generate H-L transition?
  Topic: CAN node implementation using PIC18F2585
kansusid

Replies: 9
Views: 14565

PostForum: General CCS C Discussion   Posted: Thu Aug 13, 2009 3:31 am   Subject: CAN node implementation using PIC18F2585
Thanks for the details. Is it possible to have some thought over only 3 times output in normal mode? Since few others have had this problem(can be seen in the forum postings), is it a common bug? My c ...
  Topic: CAN node implementation using PIC18F2585
kansusid

Replies: 9
Views: 14565

PostForum: General CCS C Discussion   Posted: Thu Aug 13, 2009 12:08 am   Subject: CAN node implementation using PIC18F2585
that's fine. I have also gone through it. thanks.

What could be the problem in normal mode operation where it stops after outputting data 3 times and stops( nothing prints on the serial port moni ...
  Topic: CAN node implementation using PIC18F2585
kansusid

Replies: 9
Views: 14565

PostForum: General CCS C Discussion   Posted: Wed Aug 12, 2009 11:01 pm   Subject: CAN node implementation using PIC18F2585
The settings were based on MBTime program only. Settings were basically obtained for 4MHz, 125 kbps
No. of time quanta for 1 bit time=8, propagation delay=1 Tq, Phase segment 1 and 2 = 3 Tq each, sy ...
  Topic: CAN node implementation using PIC18F2585
kansusid

Replies: 9
Views: 14565

PostForum: General CCS C Discussion   Posted: Wed Aug 12, 2009 12:03 am   Subject: entering Loopback problem
We have implemented a CAN node using PIC18F2585 and MCP2551. Baud rate:125kbps@4MHz frequency. We have used the following code to test.

#include <18F2585.h>
#fuses XT,NOPROTECT,NOLVP,NOWDT, ...
  Topic: CAN node implementation using PIC18F2585
kansusid

Replies: 9
Views: 14565

PostForum: General CCS C Discussion   Posted: Tue Aug 04, 2009 11:43 pm   Subject: CAN node implementation using PIC18F2585
Could anyone help in implementation of a CAN node using PIC18F2585?
It is planned to test the node in Loop-back mode. What CCS program to use? Ex.CAN.c or EX.can_ccs_a.c or Ex.can_ccs_b.c ?? header ...
  Topic: problem with ad7715 adc
kansusid

Replies: 3
Views: 6762

PostForum: General CCS C Discussion   Posted: Wed Jun 21, 2006 9:34 pm   Subject: problem with ad7715 adc
Thank you very much. It Works now!!!
  Topic: problem with ad7715 adc
kansusid

Replies: 3
Views: 6762

PostForum: General CCS C Discussion   Posted: Mon Jun 19, 2006 6:13 am   Subject: problem with ad7715 adc
well i am using an ad7715-3 with a pic16f877a ic the code used is similar to the one posted in the driver of ccs compiler
li'l abt ad7715
the code is


#include <16f877A.h>
#device 16f87 ...
 
Page 1 of 1
All times are GMT - 6 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group