Author |
Message |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Tue May 09, 2006 9:18 am Subject: 485 comm, problem found |
im using regular c in hitide, so there is no premade delay_ms function. but if my pulse/bits are correct (correct width in seconds), there isnt a need to do a delay check to see if my clock is correct ... |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Tue May 09, 2006 6:30 am Subject: 485 comm, problem found |
If TX9 (9-bit Transmit enable bit) and RX9 (9-bit Receive Enable bit) are both set to zero = Selects 8-bit transmission/reception. How could I be sending 9-bits, and how would that 9th bit be set high ... |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 12:58 pm Subject: 485 comm, problem found |
I have been looking at my tx and rx lines on the scope. I am comparing the readings from the 18f4610 to the ones on its predecesor, the 17c756(which is proven communication). On the transmit, either ... |
Topic: i2c...arrgghh....help!!! |
new2pic
Replies: 3
Views: 6219
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 11:18 am Subject: i2c...arrgghh....help!!! |
i dont know if this helps but this works for me:
SEN = 1;
while(comm_not_finished);
bit comm_not_finished (data passed to function)
while(!SSPIF);
SSPIF = 0;
switch (x)
{
case 0:
... |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 9:19 am Subject: 485 comm, problem found |
is the code in assembly?
also
delay_ms(10000) is a function right? wouldnt i need the function definition and prototype? |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 8:28 am Subject: 485 comm, problem found |
still I dont have an accurate way to tell time. I have not been able to find a solid delay routine. I have checked my clock chip and its frequency is correct, if I transmit 1010 1010 with a leading lo ... |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 8:09 am Subject: 485 comm, problem found |
I think the long 'high' stretch is 8 long, not 7 becuase it has the stop bit, is this correct? |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 8:03 am Subject: 485 comm, problem found |
I dont understand what is meant by this? Toggle a pin on and off to make a square wave? how do you toggle it, from a timer interrupt program? I do not know how to create an accurate delay program unle ... |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Mon May 08, 2006 6:46 am Subject: 485 comm, problem found |
are there any other things that could cause this, perhaps with the chip configuration, not a hardware problem or scope problem or osillator problem or any other external problem? |
Topic: 485 comm, problem found |
new2pic
Replies: 15
Views: 18541
|
Forum: General CCS C Discussion Posted: Fri May 05, 2006 3:18 pm Subject: 485 comm, problem found |
I am swapping out a 17C756 with a 18F4610. There are no errors with the 17C756. With the 18F4610 I will however get "comm errors" about 10% of the time. The other 90% of the time everything works fine ... |
Topic: 485 communication:gettin started |
new2pic
Replies: 10
Views: 12245
|
Forum: General CCS C Discussion Posted: Fri May 05, 2006 12:56 pm Subject: 485 communication:gettin started |
what does that mean |
Topic: 485 communication:gettin started |
new2pic
Replies: 10
Views: 12245
|
Forum: General CCS C Discussion Posted: Fri May 05, 2006 12:30 pm Subject: 485 communication:gettin started |
i dont see anything in the data sheet about CRC or checksum errors? |
Topic: 485 communication:gettin started |
new2pic
Replies: 10
Views: 12245
|
Forum: General CCS C Discussion Posted: Fri May 05, 2006 10:33 am Subject: 485 communication:gettin started |
How can i get rid of framing errors? |
Topic: 485 communication:gettin started |
new2pic
Replies: 10
Views: 12245
|
Forum: General CCS C Discussion Posted: Fri May 05, 2006 9:13 am Subject: 485 communication:gettin started |
i think this is the just of the 485 com in the 17. There is a timer that if exceeded sets "clear_485_fault" so that the transmission is repeated. "asynch_485_rec_busy" and "asynch_485_timeout_ ... |
Topic: 485 communication:gettin started |
new2pic
Replies: 10
Views: 12245
|
Forum: General CCS C Discussion Posted: Fri May 05, 2006 8:27 am Subject: 485 communication:gettin started |
this is the config for the 17c756, is this what you meant?
SYNC2 = 0; // port 2 asynchronous mode
SPEN2 = 1; // serial port 2 enable
TX2IE = 0; // disable asynch TX int ... |
|