 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 9 matches |
| Author | Message |
|---|---|
 Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
 Forum: General CCS C Discussion Posted: Mon Jun 18, 2012 1:17 pm Subject: Firmware won't start after power off/on |
| SHE is adding an index to HER pointer...and actually didn't choose that scheme but was building off code that was handed to her.
Either way, I fixed my problem. No idea how since all I did was c ... |
|
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Fri Jun 15, 2012 2:53 pm Subject: Firmware won't start after power off/on |
| perhaps you might get RID of all ICD references and USEAGE
and the debugger overhead too BTW: i am assuming that you DONT do any actual control via MCLR since the PUT fuse with an internal R ... |
|
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Fri Jun 15, 2012 11:50 am Subject: Firmware won't start after power off/on |
| The only difference in the program memory area is 3 locations that I didn't use show up at FFFF...not too concerning (unless I'm not understanding correctly). The other difference IS in the FUSES area ... | |
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Fri Jun 15, 2012 7:58 am Subject: Firmware won't start after power off/on |
| Well, that version should be OK.
Hardware: Did you design and build this board ? I mean the circuits and the PCB board layout. Or did you buy it ? If I had this problem, I would change ou ... |
|
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Thu Jun 14, 2012 2:59 pm Subject: Firmware won't start after power off/on |
| Oops, my apologies. I copied it, just must've forgotten to paste it.
CCS PCH C Compiler, Version 4.132, xxxxx 14-Jun-12 15:40 |
|
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Thu Jun 14, 2012 2:49 pm Subject: Firmware won't start after power off/on |
| Everything is connected properly. It works just fine with any other program, just not the one posted here. | |
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Thu Jun 14, 2012 2:38 pm Subject: Firmware won't start after power off/on |
| Used BROWNOUT fuse and still not working.
PIC Vdd voltage is 5.0V. Programmer is CCSLoad using both ICD-U40 and ICD-U64. CCSLoad software version: 4.037 firmware version: 2.93 no way th ... |
|
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Thu Jun 14, 2012 1:04 pm Subject: Firmware won't start after power off/on |
| Tried these and am still having the same problem. | |
| Topic: Firmware won't start after power off/on |
|
| wiseacre Replies: 23 Views: 21882 |
Forum: General CCS C Discussion Posted: Thu Jun 14, 2012 11:40 am Subject: Firmware won't start after power off/on |
| I've got a really strange problem I've been unable to figure out, along with some help from a coworker. I've written a program (that still isn't fully complete, but working) that works just fine when ... | |
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group