 |
 |
| View previous topic :: View next topic |
| Author |
Message |
samus111
Joined: 28 Aug 2014
Posts: 29
Location: Colombia
|
| PIC measuring voltage level from its own supply |
 Posted: Mon Jan 12, 2015 2:27 pm |
 |
|
Hi to everybody,
I have a project, and one of its projected features is the ability to measure its power supply level and send it by a email message. I never have used A/D converter with PICs, so, I am not sure if this can be possible. I have read a lot of posts, but all are focused in to read a external source. The problem that I see is that the Vref will change every time I try to measure the battery level. Is there some way to program a PIC with this feature or do you have a idea? Thanks. |
|
 |
newguy
Joined: 24 Jun 2004
Posts: 1909
|
|
|
samus111
Joined: 28 Aug 2014
Posts: 29
Location: Colombia
|
|
| Posted: Mon Jan 12, 2015 3:32 pm |
|
|
| newguy wrote: | http://www.ccsinfo.com/forum/viewtopic.php?t=24560&highlight=reference+supply
Measure a known voltage reference with your A/D. As battery (supply) level drops, A/D reading will rise. |
Thanks for your collaboration, basically the post you quote is for indicate a low battery alarm, well I will explain my project better:
The uC will control a transmitter, both components will be fed by 4,2V ( a single cell LiPo battery), The transmitter will work until the battery gets around 3,7V, and I need to measure constantly the power level. So, I want take the voltage value (not the low battery indicator). The Vref always will vary if I set it with the Vcc from the PIC, I wonder if maybe there is a internal zener diode that I could configure from the PIC or something alike, thanks. |
|
|
ezflyr
Joined: 25 Oct 2010
Posts: 1019
Location: Tewksbury, MA
|
|
| Posted: Mon Jan 12, 2015 3:49 pm |
|
|
Hi,
You haven't told us which PIC you are using, so all we can offer are general comments/guidelines. Most PICs will allow you to specify the A/D reference source. By specifying an external source, such as a precision voltage reference, your A/D readings will be independent of the Vcc supply voltage. The external source is then applied to the appropriate PIC pin.
Search around the forum a bit, as this topic has been well covered in the past!!
John |
|
|
samus111
Joined: 28 Aug 2014
Posts: 29
Location: Colombia
|
|
| Posted: Mon Jan 12, 2015 3:56 pm |
|
|
| ezflyr wrote: | Hi,
You haven't told us which PIC you are using, so all we can offer are general comments/guidelines. Most PICs will allow you to specify the A/D reference source. By specifying an external source, such as a precision voltage reference, your A/D readings will be independent of the Vcc supply voltage. The external source is then applied to the appropriate PIC pin.
Search around the forum a bit, as this topic has been well covered in the past!!
John |
sorry, I forgot, I am using the 12f1840, I have read the datasheet of it, but I don't find if a ability just like you have commented can be possible with this PIC's family. |
|
|
gpsmikey
Joined: 16 Nov 2010
Posts: 588
Location: Kirkland, WA
|
|
| Posted: Mon Jan 12, 2015 4:34 pm |
|
|
If you are still in the design phase you might want to go back and look through the various PICs on Microchip - some of them have a built in precision reference that you can enable. A quick snoop turns up the 12(L)F1822 and 16(L)F1823 that appear to have internal references. I have not used those 2, but there are a possible solution. I know there are others as well (I have used the 18F14K22 and it has an internal vref as well you can enable although older version 4 of the compiler did not correctly handle it (I had to set the bits myself to enable it).
mikey
_________________
mikey
-- you can't have too many gadgets or too much disk space !
old engineering saying: 1+1 = 3 for sufficiently large values of 1 or small values of 3 |
|
|
PCM programmer
Joined: 06 Sep 2003
Posts: 21708
|
|
| Posted: Mon Jan 12, 2015 5:22 pm |
|
|
| Quote: | The problem that I see is that the Vref will change every time I try to
measure the battery level.
|
12F1840 data sheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/40001441E.pdf
| Quote: |
14.0 FIXED VOLTAGE REFERENCE
(FVR)
The Fixed Voltage Reference, or FVR, is a stable
voltage reference, independent of VDD, with 1.024V,
2.048V or 4.096V selectable output levels. The output
of the FVR can be configured to supply a reference
voltage to the following:
• ADC input channel
• ADC positive reference
• Comparator positive input
• Digital-to-Analog Converter (DAC)
• Capacitive Sensing (CPS) module |
|
|
|
newguy
Joined: 24 Jun 2004
Posts: 1909
|
|
| Posted: Mon Jan 12, 2015 6:14 pm |
|
|
| samus111 wrote: | | newguy wrote: | http://www.ccsinfo.com/forum/viewtopic.php?t=24560&highlight=reference+supply
Measure a known voltage reference with your A/D. As battery (supply) level drops, A/D reading will rise. |
Thanks for your collaboration, basically the post you quote is for indicate a low battery alarm, well I will explain my project better:
The uC will control a transmitter, both components will be fed by 4,2V ( a single cell LiPo battery), The transmitter will work until the battery gets around 3,7V, and I need to measure constantly the power level. So, I want take the voltage value (not the low battery indicator). The Vref always will vary if I set it with the Vcc from the PIC, I wonder if maybe there is a internal zener diode that I could configure from the PIC or something alike, thanks. |
Think about it - this approach will enable you to measure the supply voltage accurately. See what you can come up with and if you have trouble post what you have and we'll help. |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
