| View previous topic :: View next topic |
| Author |
Message |
saeidjabbari
Joined: 25 Mar 2010
Posts: 8
|
| TIMER0 Interrupt Problem |
 Posted: Sun May 09, 2010 12:25 pm |
 |
|
Hi for all
First of all excuse me about my English.
I want to use timer0 interrupt but it isn't work well!
where is the problem?
| Code: |
#include <16f877a.h> // Define PIC Microcontroller Header
#fuses HS // Set Oscillator On "High Speed" Mode
#use delay(clock=20000000) // Set 20MHz Oscillator For Microcontroller
#include <LCD.c> // Define LCD Header
#define use_portd_lcd TRUE // Set PORTD For LCD Input Pin
#int_timer0
void Timer0_isr()
{
int i=0;
lcd_init();
while(i<11){
printf(lcd_putc,"\fCOUNT=%u",i);
delay_ms(100);
i++;}
return;
}
//---------------- PIN CONFIG ----------------
#byte PORTA=0x05 // Call PORTA Register From BANK0
#byte PORTB=0x06 // Call PORTB Register From BANK0
#byte PORTC=0x07 // Call PORTC Register From BANK0
#byte PORTD=0x08 // Call PORTD Register From BANK0
#byte PORTE=0x09 // Call PORTE Register From BANK0
#byte TRISA=0x85 // Call TRISA Register From BANK0
#byte TRISB=0x86 // Call TRISB Register From BANK0
#byte TRISC=0x87 // Call TRISC Register From BANK0
#byte TRISD=0x88 // Call TRISD Register From BANK0
#byte TRISE=0x89 // Call TRISE Register From BANK0
//----------------------------------------------------
#bit TMR0IF=0x0B.2
void main()
{
TRISA=0;
TRISB=0;
TRISC=0;
TRISE=0;
PORTC=0;
setup_timer_0 (RTCC_INTERNAL|RTCC_DIV_256);
interrupt_active(INT_TIMER0);
enable_interrupts(INT_TIMER0);
enable_interrupts(GLOBAL);
for(;;)
{
PORTB=0b00000001;
delay_ms(1000);
if(get_timer0()==0){set_timer0(0);};
PORTB=0b00000000;
delay_ms(1000);
}
}
|
This link is CODE and SCH:
http://www.4shared.com/file/bTwzl32U/TIMER0INTRRUPT.html |
|
 |
PCM programmer
Joined: 06 Sep 2003
Posts: 21708
|
|
| Posted: Sun May 09, 2010 1:25 pm |
|
|
| Tell us the purpose of your project. What do you want to do ? |
|
|
saeidjabbari
Joined: 25 Mar 2010
Posts: 8
|
|
| Posted: Sun May 09, 2010 10:42 pm |
|
|
Hi my friend
It's easy! I want when timer0 is overflow, jump to interrupt loop and count 0 to 10, and go back to main loop and turn off led. But it's not done correctly.
If download schematic and code you can understand my opinion.
Thanks For Advice |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19561
|
|
| Posted: Mon May 10, 2010 1:55 am |
|
|
| Code: |
int1 timer_overflow=false;
#int_timer0
void Timer0_isr() {
timer_overflow=true;
}
void main() {
int i;
output_b(0);
output_c(0);
output_d(0);
output_e(0);
setup_timer_0 (RTCC_INTERNAL|RTCC_DIV_256);
enable_interrupts(INT_TIMER0);
enable_interrupts(GLOBAL);
for(;;) {
if (timer_overflow) {
timer_overflow=false;
output_high(PIN_B0);
lcd_init();
for (i=0;i<11;i++){
printf(lcd_putc,"\fCOUNT=%u",i);
delay_ms(100);
}
output_low(PIN_B0);
}
}
}
|
As shown, this will wait for the timer to overflow, turn on pin B0, count for 0 to 10 on the LCD, with 100mSec between each count, then turn off the LED. Repeating whenever the timer overflows.
Best Wishes |
|
|
ckielstra
Joined: 18 Mar 2004
Posts: 3680
Location: The Netherlands
|
|
| Posted: Mon May 10, 2010 3:26 am |
|
|
I still don't get the goal of the project.
At the current settings the timer will overflow in 13ms. Keeping this in mind the 100ms delay makes no sense. |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19561
|
|
| Posted: Mon May 10, 2010 3:37 am |
|
|
Yes.
I'm so used to 18F chips, where Timer0, is 16bit by default, that the 'old' 8bit version didn't occur to me. 13.1mSec.....
Best Wishes |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19561
|
|
| Posted: Mon May 10, 2010 3:38 am |
|
|
and (of course), in the original code, it'll never get out of the interrupt routine, for the same reason.
Best Wishes |
|
|
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
