CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
USB CDC Help

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
Zezem



Joined: 02 Mar 2017
Posts: 7

View user's profile Send private message

USB CDC Help
PostPosted: Mon Mar 06, 2017 2:31 pm     Reply with quote
So I've been trying to get this pretty basic CDC project working but have ran out of ideas.

INFO:
PIC: 18F4550
Crystal 8 MHZ
Microchip Explorer 8 Dev Board

I think my fuses aren't set up right... I can't seem to get past usb_enumerated()

THANKS ALOT

Code:

#include <18f4550.h>
#include "globals.h"
#include<usb.h>
#include<usb_cdc.h>
#include <pic18_usb.h>
#include <stdlib.h>


#fuses HSPLL        //High Speed Crystal/Resonator with PLL enabled
#fuses NOPROTECT    //Code not protected from reading
#fuses NOLVP        //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#fuses NODEBUG      //No Debug mode for ICD
#fuses USBDIV      //USB clock source comes from PLL divide by 2
#fuses CPUDIV1      //No System Clock Postscaler
#fuses PLL5         //PLL5 Divide By 5(20MHz oscillator input)



#use delay(clock = 48Mhz,USB_FULL)
//Set up UARTs.
#use rs232(UART1, baud=9600, errors)
//#use rs232(baud=9600, errors)
//#use rs232(baud=1000,FLOAT_HIGH,xmit=PIN_B0,rcv=PIN_B0)


void main(void) {
    usb_init();  //used to init usb port with a device that powers itself. same as usb_init otherwise.
    usb_cdc_init();  //
    int1 usb_cdc_oldconnected=FALSE;
    int i = 0;
    int new_connected;
    int new_enumerated;
    int new_cdc;


   
    while(TRUE)
    {     
        if(usb_attached())
        {
            usb_task();
            if(usb_enumerated())
            {
                if(usb_cdc_carrier.dte_present)
                {
                    if(usb_cdc_oldconnected == FALSE)
                    {
                        printf(usb_cdc_putc,"Hello World!\n\r");
                        usb_cdc_oldconnected = TRUE;
                    }
                    if(usb_cdc_kbhit())
                    {
                        usb_cdc_putc(toupper(usb_cdc_getc()));
                    }
                }
            }
        }else
        {
            usb_cdc_oldconnected = FALSE;
            usb_cdc_init();
        }

    }
    return;
}
Ttelmah



Joined: 11 Mar 2010
Posts: 19552

View user's profile Send private message

PostPosted: Mon Mar 06, 2017 2:50 pm     Reply with quote
1) Fuses & clock should be above all the includes, except for the processor one.

The general layout in CCS C should always be:

Processor define or include
#DEVICE statements
#FUSE
#USE DELAY
#PIN SELECT's (if chip uses PPS)
#USE statements

Then includes

Then code.

Code included before clock statements, will often not function correctly...

2) Do you have a USB_ATTACHED connection?.
This is _required_ by USB, unless the device is powered from the USB cable. Usb_attached _wants_ this.

3) Generally keep to the original C standard, and declare variables at the start of code sections. Though CCS will accept them later, this can cause unexplained problems. It's a case of "keep to the standard, it's safer".

4) You have the code setup for a 20MHz crystal. It says this in the comments, yet you have an 8Mhz crystal. You need PLL2 for an 8MHz crystal.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group