 |
 |
| View previous topic :: View next topic |
| Author |
Message |
welbertdeoliveira
Joined: 29 Aug 2022
Posts: 1
|
| Renesas FS2012 + PIC16F877A I2C Issues |
 Posted: Mon Aug 29, 2022 11:32 am |
 |
|
Good afternoon.
I'm facing some problems for interface a Renesas FS2012 gas flow sensor with a PIC16F877A. The procedure for configuring the communication, based on the documentation is:
"To obtain data from the sensor, send START bit, slave address (0x07) and read bit (READ) to FS2012 and then read the two bytes of sensor data." (https://www.renesas.com/us/en/document/apn/fs2012-sample-application?language=en, page 10, "3.2 Sensor Functions").
I'm trying to configure the interface and obtain the MSB and LSB, and print on a 16x2 LCD. But, it's only possible to see FFh in both registers.
I can see the I2C protocol working by an oscilloscope.
Could anyone help me?
Best regards.
| Code: |
/*
-------------------------------------------------------------------------------------
Renesas FS2012 Gas Flow Sensor + display LCD 16x2
Biblioteca nativa do CCS C
Modo 4 bits
I/O no PortD
Conexoes físicas do LCD na PortD
lcd_enable_pin pin_B5
lcd_rs_pin pin_B4
lcd_rw_pin pin_B3
lcd_data4 pin_D4
lcd_data5 pin_D5
lcd_data6 pin_D6
lcd_data7 pin_D7
-------------------------------------------------------------------------------------
*/
#include <16F877A.h>
#use delay(clock = 4000000)
#use I2C(master, fast = 100000, sda = pin_C4, scl = pin_C3)
#fuses XT, NOWDT, PUT, NOLVP
#define lcd_rs_pin pin_B5
#define lcd_rw_pin pin_B4
#define lcd_enable_pin pin_B3
#define lcd_data4 pin_D4
#define lcd_data5 pin_D5
#define lcd_data6 pin_D6
#define lcd_data7 pin_D7
#define sensor_address 0x07
#include <lcd.c>
unsigned int8 dado_H, dado_L = 0;
void main()
{
// Habilita o LCD e imprime mensagens iniciais
lcd_init();
lcd_putc('\f');
delay_ms(100);
while(true)
{
i2c_start();
i2c_write(sensor_address);
i2c_write(1);
i2c_start();
i2c_write(sensor_address);
dado_H = i2c_read(1);
dado_L = i2c_read(0);
i2c_stop();
lcd_gotoxy(1,1);
lcd_putc("MSB: ");
lcd_gotoxy(6,1);
printf(lcd_putc, "%X", dado_H);
lcd_gotoxy(1,2);
lcd_putc("LSB: ");
lcd_gotoxy(6,2);
printf(lcd_putc, "%X", dado_L);
}
} |
|
|
 |
PCM programmer
Joined: 06 Sep 2003
Posts: 21708
|
|
| Posted: Mon Aug 29, 2022 3:17 pm |
|
|
The FS2012 data sheet lists 0x07 as the slave address. That's in 7-bit format.
However, CCS i2c routines use 8-bit format, so double that to 0x0E.
Then we get:
i2c read address: 0x0E
i2c write address: 0x0F
--------------------------------------
Also, your i2c read data routine needs to be changed to this:
| Quote: | i2c_start();
i2c_write(SENSOR_WRITE_ADDRESS); // 0x0F
i2c_write(1);
i2c_start();
i2c_write(SENSOR_READ_ADDRESS); // 0x0E
dado_H = i2c_read(1);
dado_L = i2c_read(0);
i2c_stop();
|
|
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19559
|
|
| Posted: Wed Aug 31, 2022 1:24 am |
|
|
It is slightly worrying that the device is using a reserved address.
In 7bit addresses 0 to 7, and 78 to 7F are legally reserved addresses.
Devices are not meant to use these. 7 is actually reserved as the speed
control address value.
The I2C valid 7bit device addresses are 8 to 77.
That a device is being sold that uses one of the reserved addresses, is
'scary'...  |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
